Home > Adhesive Base Stick Mounts > RAP-SB-180 (Fixed Arm) Assemblies with Cradle > Apple Assemblies >

Universal 2.5 Inch Adhesive Base with RAM-HOL-AP9U Apple iPhone 4 Holder (4th Gen/4S WITHOUT Case or Cover)
Universal 2.5 Inch Adhesive Base with RAM-HOL-AP9U Apple iPhone 4 Holder (4th Gen/4S WITHOUT Case or Cover)


 
Price $19.49

STOCK STATUS: In Stock - Ships Next Bus. Day

Product Code: RAP-SB-180-AP9U
Qty:

DESCRIPTION
 
The RAP-SB-180-AP9U is a simple and attractive adhesive base mount designed for the following Apple models:
  • Apple iPhone 4

NOTE: As the manufacturer adds new units/models to the above series this cradle may fit additional models not listed above. Click here for the most current model information RAM-HOL-AP9U. Please call 224-578-9162 or complete the product inquiry form by clicking here.


RAP-SB-180-AP9U shown above.

RAP-SB-180-AP9U Includes the Following:
  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Base: 2.5 inch adhesive disk base
  • Arm: Composite arm that attaches to the adhesive disk base.
  • Adapter: Composite black powder coated universal diamond plate. Two holes measuring 1.9 inches from center to center is compatible with the AMPS hole pattern and any RAM Mount holder. This mount rotates 180 degrees. 
  • Cradle: RAM-HOL-AP9U high strength plastic holder. Place the top of the iPhone into the cradle, and then push the base into the expandable arms at the bottom of the holder. The arms will then snap into place when the iPhone is completely secured in the cradle. The cradle allows all cables (not included) to stay connected while the iPhone is in the cradle.
  • Manufacturer's Description: Minimalists in design yet incredibly useful is the RAM Lil' Buddy mount. Using an adhesive disk, put the Lil' Buddy practically anywhere you want to keep your portable electronics easy to see and always within your reach. Designed with a very small foot print, finding a home on your dash or console is easy.
Instructions
  • General recommendations to properly adhere the adhesive disc.
    1. Ensure that both the dashboard surface and the bottom of the Ram Mount base have been thoroughly cleaned and dried.
    2. Attach either side of adhesive to the base first, let it sit several hours to allow adhesive to thoroughly bond.
    3. Attach other side of adhesive (with base) to the dashboard surface.
    4. Let the adhesive disc sit several hours before adding socket arm components, etc. to allow the adhesive to properly bond to the dashboard surface.

ACCESSORIES FOR THIS PRODUCT...
Apple iPhone RAM-HOL-AP3U Cradle for 1st Generation (Non 3G) WITHOUT Case or Cover Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.) Universal Small Sized Electronic Device Holder (Fits Device Width 1.5" to 2.5") Apple iPod Nano RAM-HOL-AP5U Cradle for iPod Nano (3rd Generation WITHOUT Case or Cover)
Price $9.49

Add
Price $31.49

Add
Price $23.99

Add
Price $12.49

Add
Apple iPhone RAM-HOL-AP3U Cradle for 1st Generation (Non 3G) WITHOUT Case or Cover Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.) Universal Small Sized Electronic Device Holder (Fits Device Width 1.5" to 2.5") Apple iPod Nano RAM-HOL-AP5U Cradle for iPod Nano (3rd Generation WITHOUT Case or Cover)


Browse for more products in the same category as this item:

Adhesive Base Stick Mounts > RAP-SB-180 (Fixed Arm) Assemblies with Cradle > Apple Assemblies
iPhone Adhesive Base Assemblies