Home > Adhesive Base Stick Mounts > RAP-SB-178 (.75 Inch Snap Link Ball and Socket Arm) Assemblies with Cradle > Universal Assemblies >

2.5 Inch Adhesive Flex Stick Base with RAM-HOL-BC1U Holder for Hand Held Devices and 2 Way Radios
2.5 Inch Adhesive Flex Stick Base with RAM-HOL-BC1U Holder for Hand Held Devices and 2 Way Radios


 
Price $24.99

STOCK STATUS: Out of Stock - Email for ETA

Product Code: RAP-SB-178-BC1U
Qty:

DESCRIPTION
 
The RAP-SB-178-BC1U is a simple and attractive design that offers a semi-permanent mounting solution with a holder for hand held devices and two way radios.


RAP-SB-178-BC1U shown above.

RAP-SB-178-BC1U Includes the Following:
  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Base Description: The base includes a 2.5 inch RAM-202PSA 3M semi-permanent adhesive disk pad that attaches firmly to a flat surface. 
  • Arm: Flexible snap link arm that allows the ultimate in versatility.
  • Adapter: Composite black powder coated universal diamond plate. Two holes measuring 1.9 inches from center to center is compatible with the AMPS hole pattern and any RAM Mount holder (RAM-HOL-xxxx) for future mounting options.
  • Cradle Included: RAM-HOL-BC1U black high strength composite holder radio cradle. The Ram Mount universal belt clip is designed to hold any hand held device or carry case with a belt clip. The holder was originally designed to hold hand held radios with a built in belt clip, but will also hold the belt clip used on cell phone and MP3 players.
    • The holder has a 1 1/8 inch long x 1/16 inch wide bar across the top with slightly raised support edges to stop the connected device from sliding off the holder.
Instructions
  • General recommendations to properly adhere the adhesive disc.
    1. Ensure that both the dashboard surface and the bottom of the Ram Mount base have been thoroughly cleaned and dried.
    2. Attach either side of adhesive to the base first, let it sit several hours to allow adhesive to thoroughly bond.
    3. Attach other side of adhesive (with base) to the dashboard surface.
    4. Let the adhesive disc sit several hours before adding socket arm components, etc. to allow the adhesive to properly bond to the dashboard surface.

ACCESSORIES FOR THIS PRODUCT...
Universal Top Clamping Cradle (Fits Device Width 2.25" to 3.5" Including Most Smartphones with Cover/Case iPhone, Droid, etc.) 2.43 Inch Diameter Self Adhesive Pad for RAM-B-202, RAM-202, RAP-SB-178, RAP-SB-180, etc. COMPOSITE Snap Link Mount with Double Diamond Bases Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.)
Price $16.99

Add
Price $6.49

Add
Price $7.49

Add
Price $31.49

Add
Universal Top Clamping Cradle (Fits Device Width 2.25" to 3.5" Including Most Smartphones with Cover/Case iPhone, Droid, etc.) 2.43 Inch Diameter Self Adhesive Pad for RAM-B-202, RAM-202, RAP-SB-178, RAP-SB-180, etc. COMPOSITE Snap Link Mount with Double Diamond Bases Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.)


Browse for more products in the same category as this item:

Adhesive Base Stick Mounts > RAP-SB-178 (.75 Inch Snap Link Ball and Socket Arm) Assemblies with Cradle > Universal Assemblies
Smartphone Mounts > Adhesive Universal Cell & Smartphone Assemblies