Home > RAM Assemblies & Parts > D Ball = 2.25" Ball Assemblies & Parts / Max. Weight 15 lbs. > 2.25" D Ball Sized Assemblies >

Pin-Lock Security Kit (Keyed Knob for "D" Sized Arm) with 3.68" Dia. Base with 2.25" Dia. Rubber Ball, SHORT Sized Length Arm and Universal 11 Inch x 3 Inch Plate with Pre-Drilled Holes
Pin-Lock Security Kit (Keyed Knob for "D" Sized Arm) with 3.68" Dia. Base with 2.25" Dia. Rubber Ball, SHORT Sized Length Arm and Universal 11 Inch x 3 Inch Plate with Pre-Drilled Holes


 
Alternative Views:
Price $152.99

STOCK STATUS: In Stock - Ships Next Bus. Day


Product Code: RAM-S-D-111U-C
QTY:

DESCRIPTION TECHNICAL SPECS
 
**CLICK HERE for the Latest Fish Finder & Chartplotter Compatibility Guide for this Mount.**

Manufacturer's Description: The RAM-S-D-111U-C consists of a 3.68" diameter round base, SHORT LENGTH double socket arm, 11" x 3" rectangular base, RAM mixed combination Pin-Lock security nut and key knob. The round base contains pre-drilled holes, including two holes at 180 degrees and three holes at 120 degrees. The rectangle base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more.

RAM Pin-Lock security solutions are designed to withstand the harshest environments where RAM Mounts are commonly used. With an emphasis on aesthetics and function, RAM security nuts/knobs are low profile and only add a small amount of additional bulk to your system when compared to the standard knob included. At a fraction of the cost of currently available keyed locking knobs, the additional peace of mind and tamper resistance comes at a very affordable price.

RAM-S-D-111U-C shown above.
NOTE: Base mounting hardware is NOT included.

RAM-S-D-111U-C Features:

  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Overall Height: Approximately 8.25 inches when positioned fully extended.
  • Mounting Plate Material: Black powder coated marine grade aluminum with pre-drilled holes. NOTE: This marine grade aluminum plate can also be drilled into for a custom hole pattern.
  • Mounting Plate Dimensions: 11 inches * 3 inches with a 2.25 inch diameter "D" sized rubber ball. Max. Weight 15 lbs.
  • Mounting Plate Description: RAM-D-111BU shown below has many different combination of pre-drilled holes which will match many electronic devices.
  • Pin-Lock Included: RAP-S-NUT5U shown below. The RAP-S-NUT5U which consists of a 1/2"-20 female threaded security nut and key knob.
  • Base Plate Included: RAM-D-202U shown below is a marine grade aluminum universal is a 3.68 inch round marine grade aluminum universal plate with a 2.25 inch diameter rubber ball.

  • Arm Included: RAM-D-201U-C with Pin-Lock is the short length marine grade aluminum arm 3.1875 inches in length from socket center to socket center and 5.0625 inches in overall length. A tightening knob on the side of the arm enables the sockets to clamp firmly to the attached base and mounting plate. The arm allows for easy adjustment by loosening the side knob, a single spring inside the arm opens the sockets, allowing the arm to pivot on the attached plates. This enables the arm and mounting plate to be positioned at various angles allowing the ultimate in position flexibility. Loosen the knob completely and the arm will disconnect from the accessories in seconds!

ACCESSORIES FOR THIS PRODUCT...
RAM Mixed Combination Pin-Lock Security Nut and Key Knob for "D" 2.25 Inch and "E" 3.38" Inch Diameter Sized Arms RAM Handle Wrench for "D" Sized Ball Arms & Mounts (RAM-D-201U Series Arms) RAM Mixed Combination Pin-Lock Security Knob, Stud, Key Knob for "D" 2.25 Inch and "E" 3.38" Inch Diameter Sized Arms & Gimbal Brackets
Price $9.49

Add
Price $29.49

Add
Price $22.49

Add
RAM Mixed Combination Pin-Lock Security Nut and Key Knob for "D" 2.25 Inch and "E" 3.38" Inch Diameter Sized Arms RAM Handle Wrench for "D" Sized Ball Arms & Mounts (RAM-D-201U Series Arms) RAM Mixed Combination Pin-Lock Security Knob, Stud, Key Knob for "D" 2.25 Inch and "E" 3.38" Inch Diameter Sized Arms & Gimbal Brackets


Browse for more products in the same category as this item:

RAM Assemblies & Parts > D Ball = 2.25" Ball Assemblies & Parts / Max. Weight 15 lbs. > 2.25" D Ball Sized Assemblies
Fishing & Paddlesport > Marine - Fish Finder and Chartplotter Assemblies (Garmin, Humminbird, Lowrance, Raymarine, etc.) > 2.25" D-Ball Sized Assemblies (15 Pound Max) > RAM-D-111 Series Assemblies (11" x 3" Plate for Large Sized Gimbal Brackets)