Home > Aviation and Yoke Mounts > Aviation Assemblies with Cradle (Apple, Garmin, GPS, Smartphone, Tablet, Universal, etc.) > Yoke Mount Assemblies (Fits .5" to 2.58" Rail Diameter) > Composite Yoke Assemblies RAP-B-121 Series Assemblies (Fits 0.625" to 1.25" Rail Diameter) > Garmin Assemblies >

Universal COMPOSITE Aviation Yoke "C" Clamp Base (Fits Rail/Edge Lip from 0.625" to 1.25") with Standard Arm and with Garmin RAM-HOL-GA51U Holder (Selected nuvi 30 Series)
Universal COMPOSITE Aviation Yoke "C" Clamp Base (Fits Rail/Edge Lip from 0.625" to 1.25") with Standard Arm and with Garmin RAM-HOL-GA51U Holder (Selected nuvi 30 Series)


 
Alternative Views:

STOCK STATUS: Out of Stock - Email for ETA


Product Code: RAP-B-121-GA51U
QTY:

DESCRIPTION
 
The RAP-B-121-GA51U is a composite clamp base mount assembly that will accommodate a rail or edge lip from 5/8 inch to 1.25 inches (commonly used in aviation applications). The assembly includes a standard sized length arm, universal diamond plate and holder for the following models:
  • Garmin nuvi 30

NOTE: As the manufacturer adds new units/models to the above series this cradle may fit additional models not listed above. Please call 224-578-9162 or complete the product inquiry form by clicking here.

RAP-B-121-GA51U shown above. 

RAP-B-121-GA51U Includes the Following:

  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Color/Material: Black high strength composite.
  • Socket Ball Size: B-Ball Size = 1.0 inch Ball. Maximum suggested weight 2 lbs.
  • Includes the RAP-B-121-238U assembly below:
   
  • Clamp Base Description: RAP-B-121BU composite clamp base mount accommodates a rail or edge lip from 5/8 inch to a maximum of 1.25 inches. The 1 inch rubber ball sits at a right angle to the plane of the mount so when connected to a rail, the ball sits parallel to the rail. To mount the base, simply place the clamps around the rail or edge and then screw the large knob at the end of the threaded rod. The hand tightened clamp makes this the perfect mounting system for rental planes and unusual shaped motorbike rails. The rail does not need to be perfectly round to use this base.
  • Arm Description: RAP-B-201U composite standard length arm for 1 inch balls. The arm measures 2.875 inches between socket centers (3.6875 inches in overall length). A plastic twist knob allows you to articulate the arm in any direction. 
  • Adapter Description: RAP-B-238U composite universal diamond plate with two holes measuring 1.9 inches from hole center to hole center and accommodates the AMPS hole pattern.
  • Cradle Included: Includes RAM-HOL-GA51U high strength plastic holder. Place the top of the GPS into the cradle, and then push the base into the expandable arms at the bottom of the holder. The arms will then snap into place when the GPS is completely secured in the cradle. The cradle allows all cables (not included) to stay connected while the GPS unit is in the cradle.
  • Second Mounting Ball: Optional. Add the RAP-B-121BBU creating a double ball base. This 1 inch diameter ball allows a second mounting point to add additional accessories. The mounting point is located on top of the RAP-B-121BU base.
RAP-B-201U Additional Information: Black composite arm allows a 1 inch diameter ball accessory to be connected at either end. A tightening knob on the side of the arm enables the sockets to clamp firmly to the attached accessories. The arm allows for easy adjustment by loosening the side knob, a single spring inside the arm opens the sockets, allowing the arm to pivot on the attached accessory. This enables the arm and accessories to be positioned at various angles allowing the ultimate in position flexibility. Loosen the knob completely and the arm will disconnect from the accessories.

 
RAP-B-238U Additional Information: Black composite universal diamond plate measures 1.25 inches * 2.5 inches. This diamond plate connects to a 1 inch diameter rubber ball. The diamond plate has two holes positioned 1.9 inches from center to center. The hole pattern found on the diamond plate will connect to a large variety of third party cradles and mounts (including RAM holders RAM-HOL-xxxx) and including those with the industry standard AMPS hole pattern.
 
Manufacturer's Description: The RAM composite glareshield/yoke base is ideally suited for a day on the wing and yet easily removed for travel in the flight bag. Both strong and light weight, this new clamping base is perfect for numerous electronic devices commonly found in the cockpit. Modular in design, switch out the clamps for a perfect fit no matter what the mounting surface, or add a second ball to mount another device; brilliant. Crafted to hold firm to most glare shields, yokes, or tubing, practically any aircraft can benefit from this product. Simple to use and exceptionally versatile, RAM has created another “must have” for any pilot. Once you’ve had a chance to use this great little device, we’re confident you’ll find uses for it no matter what you fly, drive, or ride. With everything you get in this package, you may even find yourself using your new RAM Mount on a golf cart, work bench, or even exercise equipment. With RAM, there are no limits.

The composite glareshield/yoke mount will fit a rail or edge lip from 5/8" to a maximum of 1 1/4". The mounting base can also accept a second ball RAP-B-121BBU giving you the ultimate double ball base. To mount the base, simply place the clamp ends around the rail and then screw the large knob at the end of the threaded rod. The hand tightened clamp makes this the perfect mounting system for rental planes, golf buggies or unusual shaped motorbike rails.


Browse for more products in the same category as this item:

Aviation and Yoke Mounts > Aviation Assemblies with Cradle (Apple, Garmin, GPS, Smartphone, Tablet, Universal, etc.) > Yoke Mount Assemblies (Fits .5" to 2.58" Rail Diameter) > Composite Yoke Assemblies RAP-B-121 Series Assemblies (Fits 0.625" to 1.25" Rail Diameter) > Garmin Assemblies