Home > Tripod Workstations > Tripod Workstations >

  Tripod Workstation with Tough Tray RAM-234-3 Med. to Large Sized Holder
 
 
Price $172.95


STOCK STATUS:In Stock

AVAILABILITY: Ships within 24 Hours
Product Code: RAM-TRIPOD1-234-3
Qty:

DESCRIPTION
 
RAM-TRIPOD1-234-3 shown above (computer not included).

RAM-TRIPOD1-234-3 Includes the Following:
  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Bubble Level: Built in bubble level and comfortable grips make setup and handling a breeze.
  • Carrying Case: A carrying case with strap is included to house the RAM-TRIPOD1.
  • Dimensions: Three piece telescoping legs with quick release allow the legs to be independently adjusted for uneven surfaces. The tripod adjusts to following heights:
    • Minimum Tripod Height: 21 inches (without Tough Tray)
    • Maximum Tripod Height: 58 inches (without Tough Tray)
  • Hardware Included: Yes. Dual sided threaded screw with 3/8"-16 male and 1/4"-20 male thread attaches to the tripod center column. This can be used to secure cameras and other accessories.
  • RAM-202CNSU: Single 2.5 inch diameter mount with 3/8"-16 female hole and 1.5 inch diameter rubber ball. This mount attaches to the supplied 3/8"-16 male thread on top of the RAM-TRIPOD-1.
   

  • RAM-201U: Double socket arm allows a 1.5 inch diameter ball accessory to be connected at either end. A tightening knob on the side of the arm enables the sockets to clamp firmly to the attached accessories. The arm allows for easy adjustment by loosening the side knob, a single spring inside the arm opens the sockets, allowing the arm to pivot on the attached accessory. This enables the arm and accessories to be positioned at various angles allowing the ultimate in position flexibility. Loosen the knob completely and the arm will disconnect from the accessories in seconds!
    • Arm Material: Black powder coated marine grade aluminum with plastic twist knob.
    • Arm Length Socket Center to Socket Center: 4.55 inches.
    • Overall Arm Length: 5.625 inches.
     

  • RAM-202U: 2.5 inch diameter marine grade aluminum mounting plate with 1.5 inch diameter rubber ball. The plate has pre-drilled holes included the AMPS hole pattern. This mounting plate can be used to attach to RAM Tough Tray and RAM electronic holders (RAM-HOL-xxxx)
    

  • Tough Tray Description: The RAM-234-3 "Tough-Tray" will hold laptops with a width from 10 to 16 inches and also works with most 17 inch screen laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics.
  • Tough Tray Dimensions: The device dimensions the RAM-234-3 Tough Tray will accommodate are listed below:
    • Tray Depth: 10.0 inches
    • Tray Thickness: 2.125 inches
    • Tray Width (Expansion): 10 inches to 16 inches NOTE: Works with 17 inch screens
    • Side Clamp Arm Height: 0.5 inch (min) to 1.75 inches (max)
NOTE: To compare dimensions of the original Tough Tray and Tough Tray II click here.

NOTE: Please see the RAM Tough Tray 2 (RAM-234-6) for smaller electronic devices such as netbooks.

RAM-TRIPOD1-234-3 Options (NOT INCLUDED):
  • Power Caddy: RAM-234-5U attaches to the back of the Tough Tray II and holds power supplies and small accessories.
  • Screen Support: RAM-234-S2U attaches to the side of the Tough Tray II and secures the laptop lid in a fixed position.
  • Tray Lock: RAM-234-LK2U locks the electronic device into the Tough Tray II.
  • Tripod Accessories: To view additional tripod accessories click here. 

Accessories for this product...
RAM-234-3 RAM-234-5U RAP-B-121-238U RAM-234-S2U
Price $46.95
Add
Price $8.95
Add
Price $28.60
Add
Price $15.55
Add
RAM-202CNSU RAM-217U
Price $13.95
Add
Price $47.35
Add


Browse for more products in the same category as this item:

Tripod Workstations > Tripod Workstations


2.5 Inch Dia. Magnetic Base with Standard Arm and 2.5 Inch Dia. Plate with 1/4"-20 Male Aluminum Camera Stud $56.80
Flat Surface Mount (Long Length Arm) with Tough Tray for Med. to Larged Sized Devices $108.00
ATV/UTV Strap or U-Bolt Base (U-Bolt Fits .5 to 1.25" Dia., Strap Base Fits 1.57 to 3.15" Dia.), Standard Sized Length Arm & RAM-HOL-AQ1U Large Size Waterproof Holder $80.10
Universal Power Plate III Electronics Holder - Radar Detector $20.75
2.5 Inch Adhesive Flex Stick Base with Garmin RAM-HOL-GA12U Holder (Selected GPSMAP 60 and Astro Series) $21.55
2.5 Inch Adhesive Flex Stick Base with Garmin RAM-HOL-GA14U Holder (Selected GPSMAP 76(C,CS,CSX) and 96(C) Series) $19.35
2.5 Inch Adhesive Flex Stick Base with Garmin RAM-HOL-GA30U Holder (Selected nuvi 800 Series) $26.95
RAM-A-Can with 6" Flexible Arm and Garmin RAM-HOL-GA14U Holder (Selected GPSMAP 76(C,CS,CSX) and 96(C) Series) $36.70
Chevy Colorado and GMC Canyon (2004-2012) CREW CAB Laptop Mount System $264.95 + Free Shipping and Laptop Accessory!