Home > Apple Mounts and Cradles > Apple Vehicle Complete Assemblies >

  Diamond Base Plate with Standard Arm and Small Universal Electronics Device Holder
 
 
Our Price: $55.95


Stock Status: In Stock

Availability: Usually Ships in 24 Hours
Product Code: RAM-B-102-UN1U


Description Technical Specs
 
The RAM-B-102-UN1U is a universal electronics holder featuring a diamond shaped base plate with pre-drilled holes.  NOTE: Screws must be drilled into a surface for the diamond base plate to be securedPlease check other mounts available from The Mount Depot if you are looking for a suction based or adhesive based cell phone mounts.

The small side clamping cradle is designed to hold a large amount of different kinds of cell phones and electronic devices such as the iPod Mini and Nano.  This cradle has padded locking side clamps that close tightly on the item you want to hold. To release the clamp hold, simply press the button found at the bottom left side of the cradle which will spring the clamps open. At the base of the cradle are two small supports to hold the bottom of the item securely in the cradle. 
The RAM side clamping cradle is designed to be used in a closed cabin environment. The side clamping cradle is only a light weight cradle and may not hold your device in a high vibration situations as found on a motorcycle.

The RAM-B-102-UN1U includes the RAM-HOL-UN1U cradle
and RAM-B-102U. The-RAM-B-102U includes the RAM-B-238U and the RAM-B-201U.

Please see Technical Specs for more details or click on the above parts for more information.

The RAM-B-201U double socket arm has a socket at either end to allow a 1 inch diameter ball accessories to be connected. A tightening screw on the side of the arm enables the sockets to clamp firmly to a RAM 1 inch diameter ball. When loosening the side screw, a single spring inside the arm opens the sockets allowing you to pivot the ball and socket connection or completely disconnect the ball from the socket. The arm length is 3.0 inches when measured from socket center to socket center. The total length of the arm is 3.69 inches.

The RAM-B-238U
has a 1.0 inch diameter rubber ball connected to the 1 1/4 x 2 1/2 inch diamond plate. The diamond plate has two holes positioned 1.9 inches from center to center. The hole pattern found on the diamond plate will connect to a large variety of third party cradles/holders and RAM cradles/holders including those with the industry standard AMPS hole pattern. NOTE: This base plate will attach to any of the RAM plastic holder/cradle (RAM-HOL-xxxx)and the industry standard AMPS hole pattern.
 
Below are the dimensions the RAM-HOL-UN1U cradle will accommodate:
Minimum Width: 1.5 in
Maximum Width: 2.5 in
Side Clamp Height: 1.56 in
Side Clamp Depth: 1.13 in
Cradle Height: 3.62 in
NOTE: The top of the cradle is open allowing electronic devices to be taller than the height of the cradle.
 
If you require a different sized side clamping cradle there are two other options available for larger electronic devices:
Medium Composite Side Clamping Cradle (RAM-HOL-UN2)
Large Composite Side Clamping Cradle (RAM-HOL-UN3U)
Large Aluminum Side Clamping Cradle (RAM-B-120B)

You can also build your own custom mount by selecting the RAM-B-102U and any other RAM Plastic Holder (RAM-HOL-xxxx) including Apple, cell phone and GPS holders by clicking here.

 
 

Accessories for this product...
RAM-B-102U RAM-HOL-UN3U RAM-B-120BU RAM-HOL-AP3U
Our Price: $22.95
Add
Our Price: $19.95
Add
Our Price: $43.95
Add
Our Price: $6.50
Add
RAM-KNOB3LU RAM-HOL-UN2U RAM-HOL-AP4U RAM-HOL-AP5U
Our Price: $17.95
Add
Our Price: $19.95
Add
Our Price: $8.95
Add
Our Price: $7.95
Add


Browse for more products in the same category as this item:

Apple Mounts and Cradles > Apple Vehicle Complete Assemblies
Aviation and Yoke Mounts > Apple, Cell and GPS Cradles/Holders
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal) > Apple Cradles/Holders
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal) > Cell Phone Cradles
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal) > Cell Phone Cradles > BlackBerry Cradles
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal) > Cell Phone Cradles > Universal Cell Phone Cradles
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal) > Cell Phone Cradles > Apple iPhone Cradles
Marine Electronic Mounts > Apple, Cell and GPS Cradles/Holders
RAM Parts & Assemblies > B-Ball=1.0" Ball Mounts & Parts / Max. Weight 2 lbs. > B-Ball Assemblies > Flat Surface Assemblies
Apple Mounts and Cradles
Aviation and Yoke Mounts
Marine Electronic Mounts
RAM Parts & Assemblies > Cradles (Apple, Cell, GPS & Universal)
RAM Parts & Assemblies > B-Ball=1.0" Ball Mounts & Parts / Max. Weight 2 lbs. > B-Ball Assemblies